AEG washing machine error codes
21 codes that AEG publishes for its washing machines, each with what it means, the likely cause, what you can safely check and when to call a technician. Tap your code:
What people ask
What does E40 mean on an AEG washing machine? AEG: “Error codes E40 and E41 indicate that the washing machine door or lid is not properly closed or detected”, and “This safety feature prevents the appliance from starting a cycle when the door is not securely locked.” Its checks are to push the door until it clicks, remove laundry caught between the door seal and the glass, take out excess laundry, and turn off a mechanical child lock with a coin. If E40 stays after that, AEG says “The door lock mechanism may be faulty” and to book a service technician. On this page: E40 door not closed.
Source: AEG, AEG UK Support — Washing Machine Error Code E40, E41 (4 Beeps / 4 Flashes): Causes & Fixes Checked 2026-10-13.
What does E10 mean on an AEG washing machine? AEG: “Error codes E10, E11, and C1 all indicate a problem with water flow in your washing machine”: it is not filling, filling too slowly, or there is a drainage issue. The first check is the tap, fully open and with enough pressure that “you should fill ~10 litres in about a minute” into a bucket; then the filters on the inlet hose, kinks in either hose, a drain hose no more than 10 cm into the pipe and the pump filter. AEG says to contact a service centre if “Water is not entering the machine at all” or the error persists after all the checks. On this page: E10 water supply problem.
Source: AEG, AEG UK Support — Washing Machine Error E10, E11 or C1? How to Fix Water Supply & Drain Issues Checked 2026-10-13.
4 more: beeps and flashes, the padlock, the drum cleaning icon, resetting after a code
What do the beeps and flashes on an AEG washing machine mean? On a machine without a code display, the beeps or flashes stand for the code: AEG’s E10 page answers “What does 1 beep and 1 flash mean?” with “It indicates a water supply or drainage issue similar to error codes E10, E11, or C1”, and its E40 page covers “E40, E41 or emits 4 beeps / 4 flashes”. AEG’s overview: “Beeps and flashing indicators are normal warning methods used to draw attention to a detected issue.” On this page: E10 water supply problem · E40 door not closed.
Sources: AEG, AEG UK Support — Washing Machine Error E10, E11 or C1? How to Fix Water Supply & Drain Issues Checked 2026-10-13. · AEG, AEG UK Support — Washing Machine Error Code E40, E41 (4 Beeps / 4 Flashes): Causes & Fixes Checked 2026-10-13. · AEG, AEG UK Support — AEG Washing Machine displays an error code: causes and solutions Checked 2026-10-13.
What does the padlock symbol on an AEG washing machine mean? AEG: “A padlock is displayed to indicate that the ‘Child Lock’ function has been activated”, and while it is on it prevents any action other than switching the machine on and off. To turn it off on AEG 7000, 8000 and 9000 series machines, “press and hold the Stains/Prewash and the Extra Rinse buttons for 5 seconds until the padlock no longer displays”; on the 6000 series, touch Stain/Prewash until the padlock goes off. AEG notes the buttons vary by model and are always marked with the padlock on the control panel.
Source: AEG, AEG UK Support — AEG Washing machine displays padlock Checked 2026-10-13.
What does the drum cleaning icon on an AEG washing machine mean? AEG: when the icon shows at the end of a cycle, “this is a recommendation to run the ‘drum cleaning’ cycle”, and “Once the drum cleaning cycle (Cotton 90°C) has been completed, the icon disappears.” AEG gives the reason as repeated low-temperature washes, which leave detergent, fluff and bacteria in the drum and tub, and recommends a maintenance wash “at least once a month”.
Source: AEG, AEG UK Support — The “drum cleaning” icon appears on the washing machine display Checked 2026-10-13.
How do I reset an AEG washing machine after an error code? Where AEG’s article for your code recommends a reset, its overview gives the steps: disconnect power at the wall socket or circuit breaker, wait “around 1 minute”, reconnect, and check whether the problem has gone. AEG adds “Always record the complete error code before disconnecting power”, and “Repeated fault codes generally indicate that the underlying issue remains present”, which is when to book a repair.
Source: AEG, AEG UK Support — AEG Washing Machine displays an error code: causes and solutions Checked 2026-10-13.
The questions are the ones people search for AEG, Electrolux and Zanussi washing machine codes; each answer comes only from the AEG pages named under it.
Switch off and unplug before checking. Anything electrical, anything to do with gas, and any water leak at the mains: call a technician. Codes that need one are marked Technician.
Read this first
AEG washing machines show codes that start with E (E10, E20 …); machines without a display beep or flash the number of times given by the code's first digit (E10 = 1 beep, E40 = 4). Every code below is on AEG UK's own support site. Electrolux and Zanussi washing machines come from the same group and often use the same codes, but the source here is AEG's: check your own manual.
E10 E11 Water supply problem
Also shown as C1, or as 1 beep / 1 flash.
- What it means
- The machine is not filling, is filling too slowly, or has a drainage problem that upsets the fill.
- Likely cause
- A closed tap or low pressure, blocked inlet filters, kinked hoses, or a drain hose pushed too far into the standpipe.
- What you can safely check
Switch off and unplug before checking.
- Make sure the tap is fully open. AEG's test: about 10 litres should run from the tap in a minute.
- Turn off the water, take off the inlet hose and clean the small filter at the hose connection and the one in the machine's inlet valve.
- Straighten any kinks in the inlet and drain hoses behind the machine.
- The drain hose should go no more than 10 cm into the standpipe, with the drain 60–100 cm high.
- Clean the pump filter.
- When to call a technician
- If these are fine and the code stays, book a technician.
Source: AEG, AEG UK Support — Washing machine displays error code E10, E11, C1 or 1 beep / 1 flash Checked 2026-09-28.
E20 E21 E22 E23 E24 Not draining
Also shown as C2, or as 2 beeps / 2 flashes.
- What it means
- The machine cannot pump the water out; water may stay in the drum and the spin may not run.
- Likely cause
- Most often a blocked drain filter, then a blocked sink trap or drain, a kinked hose or a drain at the wrong height.
- What you can safely check
Switch off and unplug before checking.
- Clean the pump and fluff filter, turning the pump blade with a pencil if you can see it.
- Drain hose: no more than 10 cm into the drain, with the drain 60–100 cm above the base of the machine; no kinks or twists.
- Check the sink trap and household drain are not blocked (try a wash with the hose in a bowl or sink).
- If the hose has been extended, check the joint for a blockage.
- When to call a technician
- If it still does not drain, book a technician.
Source: AEG, AEG UK Support — Washing machine displays error code E20, E21 or C2, 2 beeps or 2 flashes Checked 2026-09-28.
E30 Water-pressure sensor problem or water in the base
Also shown as C3, or as 3 beeps / 3 flashes.
- What it means
- AEG's overview lists E30 as a water-pressure (level) sensor problem; its E30 article treats the machine as leaking into its base.
- Likely cause
- A leak at the supply hose, laundry caught in the door seal, or a damaged door seal — or a sensor fault.
- What you can safely check
Switch off and unplug before checking.
- Check the supply-hose connections at the tap and at the machine for leaks.
- Check no clothing is caught between the door seal and the glass, and that the seal is undamaged.
- Clean the filters in the inlet hose and water valve.
- When to call a technician
- Technician Water leak: if the code returns, call a technician.
Source: AEG, AEG UK Support — Washing machine displays error code E30 Checked 2026-09-28.
E40 E41 Door not closed
Also shown as 4 beeps / 4 flashes.
- What it means
- The door or lid is not properly closed or not detected, so the machine will not start.
- Likely cause
- The door is not pushed shut, laundry is caught in the seal, the drum is overloaded or the mechanical child lock is engaged.
- What you can safely check
Switch off and unplug before checking.
- Push the door firmly until it clicks.
- Remove laundry caught between the seal and the glass; take out excess laundry.
- If the machine has a mechanical child lock, turn it off with a coin as the manual shows.
- When to call a technician
- If it persists, the door lock may be faulty: book a technician.
Source: AEG, AEG UK Support — Washing machine displays error code E40 Checked 2026-09-28.
E50 Motor failure
Also shown as C9 or F9.
- What it means
- A motor failure has occurred.
- Likely cause
- A motor or motor-control fault.
- What you can safely check
Switch off and unplug before checking.
- Switch off at the wall socket or breaker, wait about 1 minute, switch on again.
- When to call a technician
- Technician Electrical: if the code returns, call a technician. AEG advises not using the machine until it is fixed.
Source: AEG, AEG UK Support — Washing machine displays error message E50 Checked 2026-09-28.
E60 E61 E62 E69 Heating problem
- What it means
- Any code starting E6 generally means a heating fault.
- Likely cause
- A heating fault.
- What you can safely check
Switch off and unplug before checking.
- Switch off at the wall socket or breaker, wait about 1 minute, switch on again.
- When to call a technician
- Technician Electrical: if the code returns, call a technician. AEG advises not using the machine until it is fixed.
Source: AEG, AEG UK Support — Washing machine displays error message E60 Checked 2026-09-28.
EH0 EH1 EH2 EH3 Power supply problem
EH0 may look like EHO on the display.
- What it means
- A problem with the electricity supply to the machine.
- Likely cause
- The socket or house wiring.
- What you can safely check
Switch off and unplug before checking.
- Plug a different appliance into the same socket to see whether it works.
- Do not run the machine from an extension cable.
- Unplug for 30–60 seconds, plug in again and select a programme.
- When to call a technician
- Technician Electrical: if the socket or wiring is at fault, call an electrician; if the code stays on a good socket, call a technician.
Source: AEG, AEG UK Support — Washing machine displays error message EH0 / EHO Checked 2026-09-28.
EF0 EF3 Leak, too much foam or unbalanced load
EF0 may look like EFO; also shown as 15 beeps / 15 flashes. EF3 means a water leak was detected.
- What it means
- A warning most often caused by water leakage, over-foaming or an unbalanced load.
- Likely cause
- Too much detergent, a dirty dispenser drawer, laundry caught in the door seal, or a leak.
- What you can safely check
Switch off and unplug before checking.
- Use less detergent; if there is foam, switch off and leave the machine a few hours for it to settle.
- Clean the dispenser drawer.
- Check no clothing is caught between the door seal and the glass.
- Clean the filters in the inlet hose and water valve.
- When to call a technician
- Technician Water leak: if the code returns, have the machine inspected by a technician.
Source: AEG, AEG UK Support — Washing machine displays warning code EF0 Checked 2026-09-28.
A code that is not listed here
AEG's overview groups codes by their first two characters: a code it lists as 'E60 or similar' covers E61, E62, E69 and so on.
We list only codes the source below states. If your code is not here, it may belong to a model the source does not cover: your model’s manual is the authority.
Related pages
Source
Every code on this page comes from these pages, published by AEG and read on the date shown. Meanings are written in our own words; nothing is taken from other makes, other models or third-party code sites.
- AEG: AEG UK Support — Washing machine displays an error code, how to fix it? Checked 2026-09-28.
- AEG: AEG UK Support — Washing machine displays error code E10, E11, C1 or 1 beep / 1 flash Checked 2026-09-28.
- AEG: AEG UK Support — Washing machine displays error code E20, E21 or C2, 2 beeps or 2 flashes Checked 2026-09-28.
- AEG: AEG UK Support — Washing machine displays error code E30 Checked 2026-09-28.
- AEG: AEG UK Support — Washing machine displays error code E40 Checked 2026-09-28.
- AEG: AEG UK Support — Washing machine displays error message E50 Checked 2026-09-28.
- AEG: AEG UK Support — Washing machine displays error message E60 Checked 2026-09-28.
- AEG: AEG UK Support — Washing machine displays error message EH0 / EHO Checked 2026-09-28.
- AEG: AEG UK Support — Washing machine displays warning code EF0 Checked 2026-09-28.