Wallbox Pulsar Plus charger lights: what each colour and blink means
The Pulsar Plus has one LED on its front, and Wallbox says it matches the colour of the charging wheel in the Wallbox app. Turquoise is the one to learn: solid turquoise covers plugged in and ready, paused and fully charged, and blinking turquoise is either a scheduled charge ready to start or, with Power Boost, a car waiting for power. Red is a fault; red that stays on for 30 seconds is a load-management pairing problem instead.
The light is the LED on the front of the Pulsar Plus or Pulsar Plus Socket.
Green light
Initialisation is complete and the charger is ready to use. When you power it on, the LED turns green, fades, and turns green again once ready. It stays green until you connect your car or turn the charger off.
Applies to: Pulsar Plus and Pulsar Plus Socket. What you see: green, solid (steady).
What to do
Wallbox Help Center gives no step for the owner for this light on the page cited; the meaning above is what it says.
Source:
- Wallbox Help Center: Pulsar Plus & Pulsar Plus Socket Status LED Lights – Colours’ meaning — Pulsar Plus and Pulsar Plus Socket. support.wallbox.com Checked 2026-09-29.
Turquoise light
Standby. Either your vehicle is plugged in and ready to charge, the charge session has been paused, or your vehicle is fully charged.
Applies to: Pulsar Plus and Pulsar Plus Socket. What you see: turquoise, solid (steady).
What to do
Wallbox Help Center gives no step for the owner for this light on the page cited; the meaning above is what it says.
Source:
- Wallbox Help Center: Pulsar Plus & Pulsar Plus Socket Status LED Lights – Colours’ meaning — Pulsar Plus and Pulsar Plus Socket. support.wallbox.com Checked 2026-09-29.
Turquoise light blinking
Either the scheduled charging session you created is ready to start, or, with Power Boost, your car is waiting for power and will start charging once enough is available.
Applies to: Pulsar Plus and Pulsar Plus Socket. What you see: turquoise, flashing or blinking.
What Wallbox says to do
- Wallbox says: for a scheduled charge, plug the connector into your vehicle to start the session.
- Wallbox says: if a Power Boost wait persists, use the Troubleshooting section of its chatbot, and contact Wallbox Customer Service through it if that does not solve it.
Source:
- Wallbox Help Center: Pulsar Plus & Pulsar Plus Socket Status LED Lights – Colours’ meaning — Pulsar Plus and Pulsar Plus Socket. support.wallbox.com Checked 2026-09-29.
Dark blue light blinking slowly
Charging is in progress. When the charge is complete the light turns turquoise.
Applies to: Pulsar Plus and Pulsar Plus Socket. What you see: blue, flashing or blinking.
What to do
Wallbox Help Center gives no step for the owner for this light on the page cited; the meaning above is what it says.
Source:
- Wallbox Help Center: Pulsar Plus & Pulsar Plus Socket Status LED Lights – Colours’ meaning — Pulsar Plus and Pulsar Plus Socket. support.wallbox.com Checked 2026-09-29.
Yellow light
The charger is locked. It must be unlocked, by a user it has been set up to allow, before a charge can start. With auto-lock on, it locks itself a few seconds after the last activity.
Applies to: Pulsar Plus and Pulsar Plus Socket. What you see: yellow, solid (steady).
What to do
Wallbox Help Center gives no step for the owner for this light on the page cited; the meaning above is what it says.
Source:
- Wallbox Help Center: Pulsar Plus & Pulsar Plus Socket Status LED Lights – Colours’ meaning — Pulsar Plus and Pulsar Plus Socket. support.wallbox.com Checked 2026-09-29.
White light running round fast
The charger’s software is being updated. The LED turns on and off during the update.
Applies to: Pulsar Plus and Pulsar Plus Socket. What you see: white, streaming or running along the light.
What Wallbox says to do
- Wallbox says: do not do anything until the update is complete; you can follow its progress in the Wallbox app.
Source:
- Wallbox Help Center: Pulsar Plus & Pulsar Plus Socket Status LED Lights – Colours’ meaning — Pulsar Plus and Pulsar Plus Socket. support.wallbox.com Checked 2026-09-29.
Red light
The charger is in fault mode. Wallbox says the problem could come from the charger, the car or the electricity grid.
Applies to: Pulsar Plus and Pulsar Plus Socket. What you see: red, solid (steady).
What Wallbox says to do
Electrical safety. Wallbox ties this light to the power supply, earthing or an electrical fault, or its own steps use the circuit breaker, fuse box, RCD or isolator. The steps here are only Wallbox’s own, as its page states them; semiatic gives no electrical instructions of its own.
- Wallbox says: do not try to charge in this condition.
- Wallbox says: contact Wallbox Customer Service so its team can diagnose the issue and advise on what to do.
Source:
- Wallbox Help Center: Pulsar Plus & Pulsar Plus Socket Status LED Lights – Colours’ meaning — Pulsar Plus and Pulsar Plus Socket. support.wallbox.com Checked 2026-09-29.
Red light that stays on for 30 seconds
With Static Load Management installed: a secondaries error. The secondary chargers are misconfigured and cannot pair with this charger.
Applies to: Pulsar Plus and Pulsar Plus Socket. What you see: red, for a few seconds, then changes.
What Wallbox says to do
- Wallbox says: see its Static Load Management article or the EMS installation guide for setting up secondary chargers.
- Wallbox says: if the error persists, use the Troubleshooting section of its chatbot, and contact Wallbox Customer Service if that does not solve it.
Source:
- Wallbox Help Center: Pulsar Plus & Pulsar Plus Socket Status LED Lights – Colours’ meaning — Pulsar Plus and Pulsar Plus Socket. support.wallbox.com Checked 2026-09-29.
Orange light blinking
MID meter configuration error: communication between the Pulsar Plus and its MID meter has failed.
Applies to: Pulsar Plus and Pulsar Plus Socket. What you see: orange or amber, flashing or blinking.
What Wallbox says to do
- Wallbox says: see its article on installing and configuring the MID meter.
Source:
- Wallbox Help Center: Pulsar Plus & Pulsar Plus Socket Status LED Lights – Colours’ meaning — Pulsar Plus and Pulsar Plus Socket. support.wallbox.com Checked 2026-09-29.
Green, white and turquoise blinking in turn
Stand-alone mode: this charger, the primary, could not pair with the secondary chargers of your power-sharing system. The misconfiguration is on this charger, not on the secondaries.
Applies to: Pulsar Plus and Pulsar Plus Socket. What you see: green, white or turquoise, switching between colours.
What Wallbox says to do
- Wallbox says: see its Static Load Management article or the EMS installation guide.
- Wallbox says: if the error persists, use the Troubleshooting section of its chatbot, and contact Wallbox Customer Service through it if that does not solve it.
Source:
- Wallbox Help Center: Pulsar Plus & Pulsar Plus Socket Status LED Lights – Colours’ meaning — Pulsar Plus and Pulsar Plus Socket. support.wallbox.com Checked 2026-09-29.
Sources
Wallbox’s own help pages or manual only, read on the date shown. Nothing here comes from third-party “lights explained” sites or forums.
- Wallbox Help Center: Pulsar Plus & Pulsar Plus Socket Status LED Lights – Colours’ meaning — Pulsar Plus and Pulsar Plus Socket. support.wallbox.com Checked 2026-09-29.
Find a light by colour, movement and flash count on any maker’s charger →