semiatic

X-Sense alarm signals: beeps, chirps and lights

The X-Sense XS01-WR is a wireless interlinked smoke alarm with one red LED. The same single red flash every 60 seconds means “all normal” when silent and “battery low” when it comes with a beep, so listen as well as look.

If it is sounding a full alarm: the maker’s emergency instruction

Smoke alarm

X-Sense: never ignore any alarm (XS01-WR manual). Check for signs of smoke or fire; if you see or smell smoke, evacuate immediately and call emergency services. If you are unsure what the hazard is, contact emergency services for guidance.

From Wireless Interlinked Smoke Alarm XS01-WR — User Manual and Smoke Detector Beeps and Sounds Decoded.

The X-Sense alarm on these pages senses smoke only. For a carbon monoxide alarm, follow its own maker’s instruction.

Every X-Sense signal we could source, side by side

5 signals. Tap what it means to jump to the drawing, X-Sense’s steps and the source. If your alarm’s pattern is not exactly one of these, check the manual for your model: X-Sense models do not all use the same signals.

What you seeWhat you hearWhat it means
One red flash about every 60 secondsSilentNormal operation: Normal: the red LED flashes once every 60 seconds.
One red flash about every secondFull alarm, loud and continuousReal alarm: Alarm: smoke detected.
One red flash about every 5 secondsSilentHush or silence mode: Silence mode: for about 9 minutes after the silence button was pressed during an alarm.
One red flash about every 60 secondsOne chirp about every 60 secondsLow battery: Low battery.
Two red flashes about every 40 secondsTwo chirps about every 40 secondsFault: The alarm is malfunctioning.

One red flash every 60 seconds, no sound

Normal operation · smoke

One red flash about every 60 seconds; Silent

Normal: the red LED flashes once every 60 seconds.

What you see
One red flash about every 60 seconds
What you hear
Silent

If it is sounding a full alarm instead: X-Sense’s emergency instruction, top of this page

What X-Sense says to do about this signal

  1. Nothing to do. X-Sense says to test the alarm once a week and clean it at least every 3 months.

Source:

Short quick beeps, red LED flashing once a second

Real alarm · smoke

One red flash about every second; Full alarm, loud and continuous

Alarm: smoke detected. Interlinked alarms pick up the signal and sound too. (Pressing the test button once gives 3 short quick beeps with the same flash.)

What you see
One red flash about every second
What you hear
Full alarm, loud and continuous

Do this first: X-Sense’s smoke alarm instruction, top of this page

What X-Sense says to do about this signal

  1. Once you know there is no fire: X-Sense says the silence button on the alarm that started it mutes the interlinked alarms; pressing silence on one of the others does not silence the one that started it.

Source:

On its own page: Short quick beeps, red LED flashing once a second

Silent, red LED flashing once every 5 seconds

Hush or silence mode · smoke

One red flash about every 5 seconds; Silent

Silence mode: for about 9 minutes after the silence button was pressed during an alarm. Then it returns to normal.

What you see
One red flash about every 5 seconds
What you hear
Silent

If it is sounding a full alarm instead: X-Sense’s emergency instruction, top of this page

What X-Sense says to do about this signal

  1. X-Sense warns that silence is only a convenience and does not correct a problem: always check your home after any alarm. Other interlinked alarms can still go off during the 9 minutes.

Source:

On its own page: Silent, red LED flashing once every 5 seconds

One beep and one red flash every 60 seconds

Low battery · smoke

One red flash about every 60 seconds; One chirp about every 60 seconds

Low battery. Each interlinked alarm gives its own warning, so the beeping one is the one to change.

What you see
One red flash about every 60 seconds
What you hear
One chirp about every 60 seconds

If it is sounding a full alarm instead: X-Sense’s emergency instruction, top of this page

What X-Sense says to do about this signal

  1. Replace the battery immediately: twist the alarm off its bracket, pull the tab to take out the old CR123A, fit a new one the right way round, test, and twist it back on.

Source:

Two beeps and two red flashes every 40 seconds

Fault · smoke

Two red flashes about every 40 seconds; Two chirps about every 40 seconds

The alarm is malfunctioning.

What you see
Two red flashes about every 40 seconds
What you hear
Two chirps about every 40 seconds

If it is sounding a full alarm instead: X-Sense’s emergency instruction, top of this page

What X-Sense says to do about this signal

  1. Clean the alarm (vacuum with the soft brush on the cover and vents), or replace it immediately.

Source:

On its own page: Two beeps and two red flashes every 40 seconds

Sources

Every line on this page comes from X-Sense’s own documents, read on the date shown. Nothing is taken from third-party code sites or other makes.

Made with AI tools. · Privacy