semiatic

Keurig K-Supreme and K-Supreme Plus: what the lights mean

Single-serve K-Cup pod brewer

The K-Supreme and the K-Supreme Plus are covered by two Keurig guides that describe their lights in the same words; the only difference is the number of cup sizes (four on the K-Supreme, five on the Plus). Unlike the older K-Select and K-Elite, the K-Supreme has a DESCALE notification that turns on by itself and only goes off after a full descale, and a descale mode opened by holding the 8oz and 12oz buttons with the brewer off. It switches itself off 5 minutes after the last brew — far sooner than the 2 hours of the K-Select and K-Elite.

Every Keurig K-Supreme and K-Supreme Plus light we could source, 6 in all, each with Keurig’s meaning and steps. This is the K-Supreme and K-Supreme Plus’s pattern; another Keurig machine may use the same light for something else — check the manual for your model.

Cup-size buttons blinking after you lower the handle

Normal operation

Cup, drink or strength buttons: flashing or blinking

The brewer is on and waiting for a size: lifting and lowering the handle powers it on. The K-Supreme blinks 4 sizes, the K-Supreme Plus 5.

Which light
Cup, drink or strength buttons
Colour
Colour not named by the maker
Steady or flashing
Flashing or blinking

What Keurig says to do

  1. Choose a size, then press the blinking brew button.
  2. For a bolder cup press STRONG before brewing; for iced drinks press OVER ICE and use a large plastic tumbler full of ice.

Source:

Brew button lit steadily

Normal operation

Main button or power light: steady

Brewing. The brew is complete when the buttons are no longer lit.

Which light
Main button or power light
Colour
Colour not named by the maker
Steady or flashing
Steady

What Keurig says to do

  1. Do not lift the handle while it brews: the pod holder is full of very hot water.
  2. If it will not brew at all, add 2 oz more water: Keurig says at least 6 oz must be in the reservoir.

Source:

DESCALE light on

Descale needed

Descale light or symbol: steady

The descale notification: the brewer wants descaling. Keurig also says to descale every 3 months regardless. The light only goes off once the full descaling procedure has been done.

Which light
Descale light or symbol
Colour
Colour not named by the maker
Steady or flashing
Steady

What Keurig says to do

  1. Pour a whole bottle of Keurig Descaling Solution into the empty reservoir, then a bottle-full of water; no pod; large ceramic mug on the tray.
  2. With the brewer plugged in and powered off, hold 8oz and 12oz together for 3 seconds to enter Descale Mode (see the next page).
  3. Allow about 15 to 20 minutes in all.

Source:

Buttons flashing after holding 8oz and 12oz for 3 seconds (brewer off)

Mode running

Cup, drink or strength buttons: flashing or blinking

Descale Mode is on and waiting for you to start each descaling or rinsing brew.

Which light
Cup, drink or strength buttons
Colour
Colour not named by the maker
Steady or flashing
Flashing or blinking

What Keurig says to do

  1. Press the brew button; pour the hot liquid into the sink after each brew. Repeat until the ADD WATER light comes on.
  2. Empty and rinse the reservoir, fill it to MAX with fresh water, and when the buttons flash press brew again; repeat these rinses until the DESCALE notification turns off. The brewer then leaves Descale Mode.
  3. Foam during descaling is normal. If only a little water or air comes out, unplug, rinse the reservoir, refill with water and repeat the fresh-water rinse.

Source:

ADD WATER light on

Water

Water tank symbol: steady

The reservoir has run out. The K-Supreme guides mention this light only in the descaling steps, where it means the descaling solution has all gone through and it is time for the fresh-water rinses.

Which light
Water tank symbol
Colour
Colour not named by the maker
Steady or flashing
Steady

What Keurig says to do

  1. Empty and rinse the reservoir and refill it to the MAX line with fresh water.
  2. If you are descaling, carry on with the fresh-water rinses until the DESCALE notification turns off.

Source:

No lights: brewer off or shut itself off

Off or no power

Several lights or symbols: off

Auto Off switches the brewer off 5 minutes after the last brew. If it will not come back on, it is not getting power.

Which light
Several lights or symbols at once
Colour
No light
Steady or flashing
Off

What Keurig says to do

  1. Press the power button (or lift and lower the handle) to restart it.
  2. Plug it into its own grounded outlet, on a circuit not shared with other appliances.
  3. If it still has no power, contact Keurig Customer Service.

If that does not fix it: how to contact Keurig.

Source:

When Keurig says to get help

Contact Keurig Customer Service (the guide’s wording).

Sources

Every line on this page comes from Keurig’s own documents, read on the date shown. Nothing is taken from third-party manual sites.

Made with AI tools. · Privacy