semiatic

Keurig K-Duo: what the lights mean

Single-cup pod and 12-cup carafe brewer

The K-Duo brews a single cup from a K-Cup pod or a carafe from ground coffee, and its lights tell you which side is in use: POD and CARAFE buttons, brew-size buttons, a BREW button with an indicator light, a CARAFE light that turns red while the hot plate is on, an AUTO button, an Add Water light and a small clock screen. The brew indicator is the one to watch: it pulses slowly while the water heats (about 4 minutes the first time), goes solid while brewing and goes out when the brew is done.

Every Keurig K-Duo light we could source, 8 in all, each with Keurig’s meaning and steps. This is the K-Duo’s pattern; another Keurig machine may use the same light for something else — check the manual for your model.

POD and CARAFE buttons blinking after you press POWER

Normal operation

Cup, drink or strength buttons: flashing or blinking

The brewer is asking which way you want to brew: a single cup from a pod, or a carafe. Once you pick one, the four brew-size buttons blink for the size.

Which light
Cup, drink or strength buttons
Colour
Colour not named by the maker
Steady or flashing
Flashing or blinking

What Keurig says to do

  1. Press POD for a single cup or CARAFE for the carafe, then choose the size and press BREW.
  2. For a single cup, press STRONG before BREW for a bolder cup (single cup only).

Source:

Brew indicator light pulsing slowly on and off

Heating up

Main button or power light: fading in and out

The brewer is heating the water. The first heat takes about 4 minutes; between brews it takes about a minute. The light goes solid when brewing starts.

Which light
Main button or power light
Colour
Colour not named by the maker
Steady or flashing
Fading in and out

What Keurig says to do

  1. Nothing to do: with Smart Start the brew begins by itself once the water is hot.

Source:

Brew indicator light on steadily

Normal operation

Main button or power light: steady

Brewing is under way. The brew is complete when the indicator is no longer lit.

Which light
Main button or power light
Colour
Colour not named by the maker
Steady or flashing
Steady

What Keurig says to do

  1. Wait for the light to go out before lifting the handle or removing the carafe.
  2. After hot cocoa or other sweetened pods, Keurig recommends a rinse pod or a cleansing brew to keep the needles clean.

Source:

CARAFE button lit red

Mode running

Carafe or hot-plate button light: red, steady

The carafe heating plate is on. It comes on by itself when a carafe brew finishes and stays on for 2 hours (Carafe Auto Off).

Which light
Carafe or hot-plate button light
Colour
Red
Steady or flashing
Steady

What Keurig says to do

  1. To switch the plate off, press and hold CARAFE until the red light goes out, or press POWER.
  2. If you switched it off by mistake, press and hold CARAFE until the red light comes back.

Source:

AUTO button lit and a clock icon on the screen

Setting confirmed

Icon on the display screen: steady

Auto Brew is set: the carafe will brew by itself at the time you programmed (up to 24 hours ahead). While it is set you can only brew a single cup.

Which light
Icon on the display screen
Colour
Colour not named by the maker
Steady or flashing
Steady

What Keurig says to do

  1. To cancel Auto Brew, press AUTO once; the clock icon disappears.
  2. Auto Brew needs the clock to be set first.

Source:

Mountain icon on the screen

Setting confirmed

Icon on the display screen: steady

High Altitude mode is on, for brewing above about 5,000 feet. You turn it on by holding POD and CARAFE together for 3 seconds.

Which light
Icon on the display screen
Colour
Colour not named by the maker
Steady or flashing
Steady

What Keurig says to do

  1. If short carafe brews continue at high altitude, Keurig says to contact Customer Service.

Source:

Add Water light on

Water

Water tank symbol: steady

The brewer wants water: the reservoir is low or empty, or it is not sitting properly on its base, and it will not brew until that is fixed. During descaling the same light is your signal that the descaling solution has all run through.

Which light
Water tank symbol
Colour
Colour not named by the maker
Steady or flashing
Steady

What Keurig says to do

  1. Fill the reservoir to the MAX fill line — not beyond — and make sure it is seated properly in its base.
  2. If the Add Water light stays on after refilling, contact Keurig Customer Service.

If that does not fix it: how to contact Keurig.

Source:

All the buttons blinking at the same time

Fault or blockage

Several lights or symbols at once: flashing or blinking

Listed under ‘Brewer will not brew’: a fault Keurig does not give a home fix for.

Which light
Several lights or symbols at once
Colour
Colour not named by the maker
Steady or flashing
Flashing or blinking

What Keurig says to do

  1. Contact Keurig Customer Service.

If that does not fix it: how to contact Keurig.

Source:

When Keurig says to get help

Contact Keurig Customer Service (the guide’s wording).

Sources

Every line on this page comes from Keurig’s own documents, read on the date shown. Nothing is taken from third-party manual sites.

Made with AI tools. · Privacy